MCU name: RL78/G12(ROM:16KB)
Chip name: R5F103AA

---

Module	Macro	Sub	Setting	Status
Clock Generator				Used
	CGC			Used
			Pin assignment setting-PIOR0 bit = 1	Used
			Pin assignment setting-PIOR1 bit = 1	Used
			Operation mode setting	High speed main mode 3.6 (V) ¡Ü VDD ¡Ü 5.5 (V)
			Main system clock (fMAIN) setting	High-speed OCO (fIH)
			fIH operation	Used
			fIH frequency	24(MHz)
			fMX operation	Unused
			fIL Frequency	15(kHz)
			Interval timer operation clock	15 (fIL)(kHz)
			CPU and peripheral clock (fCLK)	24000 (fIH)(kHz)
			On-chip debug operation setting	Unused
			Security ID setting	Used
			Security ID	0x00000000000000000000
			Output the function for confirming reset source	Used
			Illegal memory access detection function setting	Unused
			Setting of data flash library	Unused
Port				Used
	PORT			Used
		P11
			Mode	Out
			N-ch	Unused
			output value	0
		P13
			Mode	Out
			N-ch	Unused
			output value	0
		P14
			Mode	Out
			N-ch	Unused
			output value	0
		P15
			Mode	Out
			N-ch	Unused
			output value	0
		P23
			Mode	In
			Pull-up	Unused
			TTL buffer	Unused
		P30
			Mode	Out
			N-ch	Unused
			output value	0
		P50
			Mode	Out
			N-ch	Unused
			output value	0
		P51
			Mode	Out
			N-ch	Unused
			output value	0
		P137
			Mode	In
			Pull-up	Unused
			TTL buffer	Unused
		P147
			Mode	In
			Pull-up	Unused
			TTL buffer	Unused
Interrupt				Unused
Serial				Used
	SAU0			Used
		Channel0
			Channel 0	UART0(Transmit/receive function)
			Data length setting (Receive function)	8 bits
			Transfer direction setting (Receive function)	LSB
			Parity setting (Receive function)	None
			Stop bit length setting (Receive function)	1 bit fixed
			Receive data level setting	Normal
			Transfer rate setting (Receive function)	9600(bps)(Current error: +0.16% the minimum is -5.14% the maximum is +5.12%)
			Reception end interrupt priority (INTSR0)	Low
			Reception error interrupt priority (INTSRE0)	Unused
			Reception end (Callback function setting)	Used
			Reception error (Callback function setting)	Used
			Transfer mode setting	Single transfer mode
			Data length setting (Transmit function)	8 bits
			Transfer direction setting (Transmit function)	LSB
			Parity setting (Transmit function)	None
			Stop bit length setting (Transmit function)	1 bit
			Transmit data level setting	Normal
			Transfer rate setting (Transmit function)	9600(bps)(Current error: +0.16%)
			Transmit end interrupt priority (INTST0)	Low
			Transmission end (Callback function setting)	Used
	IICA0			Unused
A/D Converter				Used
	ADC			Used
			A/D convertor operation setting	Used
			Comparator operation setting	Operation
			Resolution setting	10 bits
			VREF(+) setting	VDD
			VREF(-) setting	VSS
			Trigger mode setting	Hardware trigger no wait mode
			Hardware trigger no wait mode	INTTM01
			Operation mode setting	Continuous select mode
			ANI0 - ANI3 analog input selection	ANI0 - ANI2
			A/D channel selection	ANI1
			Conversion time mode	Normal 1
			Conversion time	25.33333 (608/fCLK)(¦Ìs)
			Conversion result upper/lower bound value setting	Generates an interrupt request (INTAD) when ADLL ¡Ü ADCRH ¡Ü ADUL
			Upper bound (ADUL) value	255
			Lower bound (ADLL) value	0
			Use A/D interrupt (INTAD)	Used
			Priority	Low
Timer				Used
	TAU0			Used
		Channel0
			Channel 0	Interval timer
			Interval value (16 bits)	1000¦Ìs, (Actual value: 1000)
			Generates INTTM00 when counting is started	Unused
			End of timer channel 0 count, generate an interrupt (INTTM00)	Used
			Priority (INTTM00)	Low
		Channel1
			Channel 1	Interval timer
			Operation mode setting	16 bits
			Interval value (16 bits)	1000¦Ìs, (Actual value: 1000)
			Generates INTTM01 when counting is started	Unused
			End of timer channel 1 count, generate an interrupt (INTTM01)	Used
			Priority (INTTM01)	Low
		Channel4
			Channel 4	PWM output (master)
			Cycle value	1000¦Ìs, (Actual value: 1000)
			End of timer channel 4 count, generate an interrupt (INTTM04)	Unused
			Duty value	50(%), (Actual value: 50%)
			Initial output value	0
			Output level	Active-high
			End of timer channel 5 count, generate an interrupt (INTTM05)	Unused
		Channel5
			Channel 5	PWM output (slave)
		Channel6
			Channel 6	PWM output (master)
			Cycle value	100¦Ìs, (Actual value: 100)
			End of timer channel 6 count, generate an interrupt (INTTM06)	Unused
			Duty value	50(%), (Actual value: 50%)
			Initial output value	0
			Output level	Active-high
			End of timer channel 7 count, generate an interrupt (INTTM07)	Unused
		Channel7
			Channel 7	PWM output (slave)
Watchdog Timer				Used
	WDT			Used
			Watchdog timer operation setting	Used
			Operation in HALT/STOP/SNOOZE mode setting	Stopped
			Overflow time	136.53 (2^11/fIL)(ms)
			Window open period	100(%)
			Enable interval interrupt when 75% + 1/2fIL of overflow time (INTWDTI)	Used
			Priority	Low
12-Bit Interval Timer				Unused
Clock Output/Buzzer Output				Unused
Voltage Detector				Used
	LVD			Used
			Low voltage detector operation setting	Used
			Operation mode setting	Reset mode
			Reset generation level (VLVD)	2.75(V)