73 lines
2.4 KiB
C
73 lines
2.4 KiB
C
#include <appConfig.h>
|
|
#include <systemInit.h>
|
|
#include <pdsTask.h>
|
|
#include <validation.h>
|
|
#include <gtimer_device.h>
|
|
#include <motorControlTask.h>
|
|
#include <adc_device.h>
|
|
#include <pwm_aux_device.h>
|
|
#include <gpio_device.h>
|
|
#include "wdt_device.h"
|
|
|
|
uint8_t trim1V5 = 0;
|
|
|
|
|
|
void main(void)
|
|
{
|
|
#if ENABLE_FUNCTION_VALIDATION == 1
|
|
// validation_main();
|
|
#endif
|
|
|
|
|
|
|
|
/* !!!!!!!MUST BE called firstly here for initializing system parameters !!!!*/
|
|
PDS_Init();
|
|
/* System init for hardwre init */
|
|
SYS_Init();
|
|
/* system main infinite loop */
|
|
// WDTA_Enable(WDTA_INTERVAL_2304MS);
|
|
WDTA_Disable();
|
|
// IOCTRLA_SFRS->ANALOGTESTMUXOVERRIDE.ANASELREG = 0x4000;//0x4000: PB7 analog connection is switched on
|
|
// IOCTRLA_SFRS->ANALOGTESTMUXOVERRIDE.GPIOCONREG = 0X400;//0x400: Select CSA_Filter_OUT to PB7
|
|
// IOCTRLA_SFRS->ANALOGTESTMUXOVERRIDE.GPIOCONSEL = 1;// 0x1: GPIO_CON_REG controls analog test MUX.
|
|
// delay(100);
|
|
// SYSCTRLA_SFRS->DEBUG_ACCESS_KEY.DEBUG_ACCESS_KEY = 0x05;
|
|
// while(SYSCTRLA_SFRS->DEBUG_ACCESS_ENABLED == 0);
|
|
//
|
|
// SYSCTRLA_SFRS->TRIM_ACCESS_KEY.TRIM_ACCESS_KEY = 0x0E;
|
|
// while(SYSCTRLA_SFRS->TRIM_ACCESS_ENABLED == 0);
|
|
//
|
|
// TRIMHV_SFRS->TRIM_LF_RC = 0XB0;
|
|
//
|
|
//
|
|
// SYSCTRLA_SFRS->PMU_ACCESS_KEY.PMU_ACCESS_KEY = 0x0A;
|
|
// while(SYSCTRLA_SFRS->PMU_ACCESS_ENABLED == 0);
|
|
//
|
|
// TRIMHV_SFRS->PMUTRIM.VDD1V5_LDO_TRIM = 3U;
|
|
// trim1V5 = TRIMHV_SFRS->PMUTRIM.VDD1V5_LDO_TRIM;
|
|
//
|
|
// if(trim1V5 == 3){
|
|
// IOCTRLA_SFRS->CTRL_MODE[GROUP_GPIOB].PU &= ~(1U << (uint8_t)GPIO_PORT_7);
|
|
// IOCTRLA_SFRS->CTRL_MODE[GROUP_GPIOB].PD &= ~(1U << (uint8_t)GPIO_PORT_7);
|
|
// //mode config 1
|
|
// IOCTRLA_SFRS->PORT_GROUP_MUX[GROUP_GPIOB] &= ~(0x0FUL << (4U*(uint8_t)GPIO_PORT_7));
|
|
// IOCTRLA_SFRS->PORT_GROUP_MUX[GROUP_GPIOB] |= (0x01UL << (4U*(uint8_t)GPIO_PORT_7));
|
|
// //select output signal
|
|
// IOCTRLA_SFRS->TESTMUX.TESTMUX3 = 8U;
|
|
//
|
|
// IOCTRLA_SFRS->ANALOGTESTMUXOVERRIDE.ANASELREG = 0x800;//0x800: PB4 analog connection is switched on
|
|
// IOCTRLA_SFRS->ANALOGTESTMUXOVERRIDE.GPIOCONREG = 2;//0x2: Select VDD1V5 to PB4
|
|
// IOCTRLA_SFRS->ANALOGTESTMUXOVERRIDE.GPIOCONSEL = 1;// 0x1: GPIO_CON_REG controls analog test MUX.
|
|
// }
|
|
// WDTA_Enable(WDTA_INTERVAL_2304MS);
|
|
// VDD3V3EXT_ON;
|
|
|
|
for(;;){
|
|
TM_RunTasks();
|
|
}
|
|
}
|
|
|
|
|
|
|
|
|